I'm looking to get help with a box design for a single American Bass XFL1522. I would like to be at around 3.5ft^3 and tuned to about 30Mhz. I listen to 95% rap but am welcome to opinions about tuning. The dimesnions I have available are 36" width, 15" height and 37" depth. I will be using 3/4"...
Im looking for a box design for my 2 sa12's..going on top of the back seat of my extended cab f150 and I will be using 2 4" aero ports, I would like the tuning to be 29-30 hz and they will be running off of an American bass phantom 4k. If possible I would like the box to be between 4-4.5 cubic feet.
I am looking at using a box off of the free box design but I am going to change it a little. I was going to do away with the center support and use a 8"(7.75 id) aero port rather than the slot ports. It will be 16" long. Will with effect the box at all? I think that my tunning will be about...
Ok so all I have ever used to build boxes is MDF, and now the more I look the more I see that people are using Birch plywood. Just wondering why this is, Is it structurally more sound, why go with it if it costs so much more. And we all hate the dust, I know don't need to tell me.
well iv been tryin to figure out a box design want one with subs up and port back needs to be about 6.5 cubes after displacement tuned at about 32 to 34 hurtz its in a 2001 jeep grand Cherokee if anyone could help thanks much need help plzz
max dementions- 24 deep and 40 wide and watever tall...
1. Car. Year, Make, Model:
2. Subs. Make, Model, Size, How many:
Rockford Fosgate, T1, 12", 2
3. Power. How much power per sub:
American Bass CFL 120.1, around 900rms a piece
4. Goal. SPL or SQ:
5. Sealed or ported:
6. Sub/port placement:
What ever is...
1. Car. 2010 Honda Civic Coupe
2. Subs. 2 L7 15s
3. Power. 900
4. Goal. SPL or SQ: ither - want some quality but want it loud
5. Sealed or ported: Whatever works
6. Sub/port placement: Whatever works
7. Max dimensions: 34 L x 28 W x 16 H
8. Desired NET vol and tuning(optional):
Hey guys I have a 2001 Dodge Intrepid and am going to start design of my box soon and need some input. I will be throwing a Sundown 3000d at my BTL 12". I want to do two ports through the rear deck and was wondering if anyone has done this and can help me understand how to do this better. I want...
iv been designing a new box for my hdc3 18 and im stumped on how the Slot Port should be.
i know that i need at least 18 square inches of port area per cubic foot.
the box is 46"L, 20"W, 18"H (7.8ft^3)- going in the back seat of my car
tuning to 32 Hz.
what im looking for is the dimensions...
Its time for the hdc3 15 d2 to find a suitable home. Currently in a very non ideal 4.6 cuft @ 30 hz with 88 sq.in. of port! sounds halfway decent on about 5 notes. no bueno at all. wanted to know what u guys think would be the most optimal size, tuning, configuration. On a 2200d @ 1ohm in the...
im designing a new box for my HDC3 18, going around 6-6.2 cubes and have 3, 4" flared ports to go with it. planned on something Low for Daily (35Hz) and for SPL (45Hz)... would like to get your opinions on weather 45hz is a good tone for SPL or not.
thanks for advice in advance.
i plan on building a new box for my HDC318, its gonna be roughly 6.6 cubes with 3 flared ports tuned to 35hz daily and 45hz SPL. im confused on weather i should keep the box in the trunk (intrepid 4 door) or build it in the back seat and sealing off the trunk from the cabin. im going for pure...
I will be getting 4 15 inch memphis pr subs and would like to make a box
i have a 99 ford explorer and can use the whole trunk.
does anyone have any cb/ft - tuning frequency suggestions (primary focus being spl)
i would appreciate all the help i can get.
Hey, im going to be building a box for a OZ 18" that im buying from ridnclean.The amp being used is going to be a F2500D. Will be wired to 1ohm so roughly around 2500-2800rms depending on my voltage(maybe less on big hits). I need help with my port tuning. Im going to be doing precision...