Car Audio Classifieds! banner
Status
Not open for further replies.
1 - 20 of 27 Posts

·
Banned
Joined
·
4,511 Posts
Discussion Starter · #1 · (Edited)
1. Product:
10" lms


2. Specs:
SVC4ohm
500rms
Mid break in
Re:2.94 ohms
Fs: 28.0 Hz
SPL: 86 dB
Vas: 1.44 cu. ft.
Qms: 7.00
Qes: 0.45
Qts: 0.40
Xmax: 29mm




3. Description/Condition:

Never mounted powered to break in and pull parameters. Waiting for Matt to send me fully broken in parameters and I will post them.
Uses a tc9 motor with three .75" slugs



4. Price: :
SOLD


5. Pictures:























** DO NOT DELETE ANYTHING BELOW THIS LINE OR THREAD WILL BE DELETED **
-----------------------------------------------

This message is automatically inserted in all classified threads.

Please be advised, all buyers and sellers should satisfy themselves that the other party is genuine by providing the following via PM to each other after negotiations are complete and prior to dispatching goods and making payment:

1) Telephone number. Call the number back at a unspecified time and make sure that it is the person's correct phone number.

2) Name and address including postal code

3) Valid e-mail address. Send an e-mail requesting a response to information about the deal being made.


DO NOT proceed with a deal until you are completely satisfied with all details being correct. It's in your best interest to check out these details yourself.

If transaction was completed on CACO, please use iTrader to record feedback.

Potential buyers/seller should check iTrader feedback also before continuing transaction.
 

·
Banned
Joined
·
4,511 Posts
Discussion Starter · #3 ·
Not looking for any trades but shoot me any offers via private message and send me some pictures too :)
 

·
Banned
Joined
·
4,511 Posts
Discussion Starter · #8 ·
ttt
 

·
Banned
Joined
·
4,511 Posts
Discussion Starter · #10 ·
Easily 500rms did it on the ap 30001 in the 1ft^[email protected] box and it absolutely slammed on the lows
 

·
Banned
Joined
·
4,511 Posts
Discussion Starter · #11 ·
beefcake
 

·
Premium Member
Joined
·
2,328 Posts
do u think it could take 1200rms
 

·
Banned
Joined
·
2,030 Posts
back off Loud..... I'm trying to get this for my shelf :(


don't think 1200wrms would be wise on a 10" lms with a single soft spider, I think this one was built for low fs
 

·
Premium Member
Joined
·
2,328 Posts
lol i need something nice for the misses 807
 

·
Banned
Joined
·
2,030 Posts
ok, fine... but only because it's getting up on v-day... much <3 to you and yours.


TC, ill pass, but can likely get that machine work handled for you still :)
 

·
Banned
Joined
·
1,245 Posts
do u think it could take 1200rms
I think with the single soft spider along with the lms coil I'd give it a rating of 600-700 but this sub is a low end monster and doesn't need much power to get down.
 

·
Banned
Joined
·
4,511 Posts
Discussion Starter · #17 ·
do u think it could take 1200rms
Sorry but I seriously doubt it unless you went with a small sealed enclosure.

Thermally yes mechanically no. You honestly do not need a lot of power with this driver. It's pretty efficient design, most lms drivers are horrible when it comes to efficiency. I had it on a ap3001 last night in a 1.3ft^[email protected] and it was really nice. Reminded me of my 3hp proto 10" It had but way better low end granted output wasn't up to par like my old driver.

ok, fine... but only because it's getting up on v-day... much <3 to you and yours.


TC, ill pass, but can likely get that machine work handled for you still :)
If you end up changing your mind let me know and let me know of the cost to get this done :)
 

·
Banned
Joined
·
2,030 Posts
I'd love to have this sub, but if Cavi wants it, he can have first crack, otherwise, lets deal.. and he wont charge me for the machine work, so I wont charge you.
 
1 - 20 of 27 Posts
Status
Not open for further replies.
Top